Incoloy 800H Flat washers
ISO 7089 / ISO 7090ASTM B409
For Incoloy 800H washers, controlled-carbon, coarse-grain performance for creep duty is only useful with a bearing section that stays flat under load. Bore, outside diameter and thickness match the head or nut to the supported member.
- MOQ
- 100PCS
- Samples · typical
- ~20 days
- Production · typical
- 25–35 days
- Heat treatment
- Solution annealed
EN 10204 3.1 MTC + heat-number traceability
Which standard is on your order?
Raw Material Specifications
Dimension Reference
Heat Treatment
Solution annealedThe specified solution treatment develops the controlled grain structure needed for sustained high-temperature creep duty.
What we can make in Alloy 800H
Normal series
Use under bolt heads and nuts on machined equipment faces with adequate surrounding seat area. The bore must clear the bolt shank and under-head radius so the washer lies flat.
Larger outside diameter
Use over slots, oversized holes and softer mounting surfaces to spread the bearing load. Washer thickness matters as well as diameter: a thin wide washer can dish over an unsupported opening.
Square & special profiles
Use on channel supports, slotted bases and special mounting pads where a round washer leaves insufficient support. Profile and hole position keep the bearing plate seated across the actual opening.
- Geometry
- Bore × outside diameter × thickness
- Forms
- Round · Square · Drawing profiles
- Function
- Bearing surface · Spacing
- Sizing
- Metric · Inch
- Final condition
- Solution annealed
- Inspection
- Bore · Outside diameter · Thickness · Burrs
Manufacturing route
Small lots can be machined from suitable stock; repeat production uses cut or punched blanks with bore and outer edge finishing.
Heat treatment & final condition
The final solution-treated condition and grain-size requirement are recorded for the ordered H or HT grade. Final dimensions are inspected after the last thermal operation.
Finished geometry
Thickness, flatness and edge finish establish the bearing geometry; the washer is not labelled hardened solely because the alloy is corrosion resistant.
Where 800H fits — and what matters
Furnaces & Heat Treatment
Heat-treatment fixturesIncoloy 800H flat washers spread bolt or nut bearing load across heat-treatment fixtures, protecting the seating surface and bridging the specified hole clearance. Hot dwell, thermal expansion and repeated furnace cycles set the working load.
Power & Turbines
Boiler-duct supports and hot auxiliary bracketsIncoloy 800H flat washers spread bolt or nut bearing load across boiler-duct supports and hot auxiliary brackets, protecting the seating surface and bridging the specified hole clearance. Hot dwell and start-stop expansion act on the supported or moving component.
Chemical Processing
Reformer tube-support and heater fixturesIncoloy 800H flat washers spread bolt or nut bearing load across reformer tube-support and heater fixtures, protecting the seating surface and bridging the specified hole clearance. These parts work in the heated equipment zone, where sustained loading and thermal expansion govern their section and clearance.
Same washer. Different material priorities.
Incoloy 800H material dataIncoloy 800
UNS N08800- Carbon
- ≤0.10%
- What changes
- General heat and oxidation resistance; no grain-size requirement in the family comparison.
Incoloy 800H
UNS N08810 · Current grade- Carbon
- 0.05–0.10%
- What changes
- Controlled carbon and coarse-grain condition for creep and stress-rupture duty.
Incoloy 800HT
UNS N08811- Carbon
- 0.06–0.10%
- What changes
- Tighter carbon and Al + Ti control (0.85–1.20%), with solution treatment and coarse grain for creep duty.
From drawing to documented delivery
- 01Drawing & BOMForm, dimensions and quantity
- 02Material & formingGrade, heat and manufacturing route
- 03Final inspectionGeometry, threads and ordered tests
- 04Documents & dispatchLot records and identified packing
Order documents
- Material identity
- UNS N08810 · heat number · ordered condition
- Final-part acceptance
- UNS grade, carbon and alloy chemistry, solution-treatment record and ordered grain-size evidence.
- Dimensional record
- Bore · Outside diameter · Thickness · Burrs
- Traceability
- EN 10204 3.1 material certificate · production lot · identified packing
Build your 800H washer enquiry
Questions about 800H flat washers
Should the washer use the same alloy as the bolt?
The wetted assembly may need matching corrosion resistance, but the washer also needs sufficient bearing strength and thickness. The bolt grade does not by itself specify a hardened or load-rated washer.